How To Install Diagbox V7.57 Software For Leixa 3 PP2000

1. Open file “Diagbox V7.57” and run “setp 1”, you just operate according to the tips to finish installation (Next >> Agree >> OK).

2. When finished Step 1, the PC will restart. Until it pops out the window, click Next >> I Agree >> Next >> Next >> Install >> Finish to complete installation.

3. Next, it will pop out a window “Alcohol 52%”, right click and choose “Add Images”, and then load “Step2 DBV0702”(locate on Diagbox V7.57)


4. To mount on “Step2 DBV0702” (right click), and then pop out “Installer language”, just click “Cancel”.

5. Open “DiagBox_V07.02”,


6. Next to run “Diagbox_setup”, and then select language and click “OK” to continue.

7. Install “Diagbox Setup”. When finished, it come out “Activation” window. Try to click the icom (mark red) and to input the customer code and click “”to continue. You just wait until the software complete installation (about 12 minutes).



8. After well completed, it takes out “PAREMETERS” interface (finish the info).


9. Both click “×” , check as the following picture.



10. It will enter into “BRAND SELECTION” interface, and to close the window.

11. Run “Diagbox” on the desktop, it is going on the update to V7.02


12. Next, operation is the same as that of Step 9, and to close the window.

13. Operate “Diagbox V7.57” (check the picture of Step 5), and open file “setp3 update V7.02 to V7.57” and run “Diagbox Update V7.xx to 7.44”.


14. It take out a new interface, just to continue according to the tips, until it appear the interface as below showing to input “installation password”, and to complete installation. (Note: Remember to choose “No, I will restart the computer later” before click “Finish”).


15. And back to run “Diagbox Update V7.44 to 7.49”, the subsequent operation is as the time as “Step 14

16. Finally, run “Diagbox Update V7.49 to 7.57” and complete installation.

17. Open “DiagBox”, and it will automatically go on installation (Note: You need to wait for completing installation, usually 8 minutes).

18. After completing, It automatically enters into the main interface; you connect the device to the car, and use the short USB cable to connect with the pc. It will prompt to install driver.

1819. You can choose your brand and the specific models on this interface. It can work for your car with the Leixa-3 PP2000 Diagbox V7.57 software.




How to Program New Peugeot Key Using Lexia 3 PP2000

Here share with you how to program new Peugeot key using Lexia 3 PP2000.

Note: before starting, you need to download and install software, here offer video guide (divide into 2 parts) for your reference:



Note: now Lexia 3 is available to update to the newest V48 (via CD that you will get if you buy at


Setup video guide:


The following part is all about the operation guide:

1. Open the software and enter into vehicle interface (here take Peugeot 307 as an example).


2. Connect the Peugeot Planet interface to the PC and to the vehicle, and then turn ignition on.


3. Next, it will pop out information of your vehicle.


4. Select Peugeot Planet 2000 and click OK to continue.


5. Select Test by ECU >> Built-in systems interface >> Learning >> Programming of keys.


6. Enter the key number to be learnt (Note: the number of keys to be programmed cannot exceed 5), and then click OK to proceed.


7. Key programmed, you need to turn ignition off and take out the key.


8. Insert the next key in the ignition (if you input 1 at Step 6, this step can be neglected). Key programmed, you need to turn ignition off and take out the key.


9. The information will be shown at picture below.


10. Next is the imperative you should keep in mind.


11. The following part is about Re-synchronize the HF remote controls procedure.


So far, it finished.

how to solve Lexia 3 Diagbox error 20 (failure of the activation).

Q: During the installation of Lexia 3, I got ERROR reading “Failure of the activation (error 20)

 Lexia-3 Diagbox error 20

A: lexia3 pp2000 software and diagbox v6.01 software was stored in the same one CD, and it is easily to get diagbox error 20, the solution is to download diagbox V6.01 software.(the two software is separately stored in two different CD) , try to reinstall and the problem will be solved.

Q1: when install Lexia-3 Diagbox software, error message reading “ERROR Lexia: error during installation of Lexia. You have to reactivate to restart the installation.”

Lexia3 error

A1: Your computer system isn’t compatible with the software; please use Windows XP operation system.

Q2: Does Lexia test the tire pressure?
A2: If your car has Tire pressure control unit, lexia-3 can test the tire pressure.

Q3: Does Lexia-3 work with Peugeot 308?
A3: Yes, it does, but which year of your Peugeot 308? Lexia-3 PP2000 works with Peugeot 308 from 1996 to 2008.

Q4: Can Lexia-3 (item NO: SP08-C) work with Peugeot Partner Tepee B9 2011 diesel car?
A4: this car model is included in the supported carlist, so far no users feedback this car is not supported.

Q5: is PPS compatible with Peugeot 307 HDI?
A5: PPS2000 work with Peugeot 307, but it is not compatible with Hybrid Diesel Peugeot only with the gasoline car.

Q6: Can Lexia-3 PP2000 (item NO. SP08-C) work with Peugeot 407 2005, after install the NEW DPF, can I reset DPF counter? After Eolys is full, can I reset Eolys counter?
A6: PP2000 supports Peugeot 407 2005, but the DPF and Eolys are truck or diesel car systems, we haven’t tested it.

Q7: Would you please store the software lexia3 pp2000 and diagbox6.01 in one CD?
A7: No, they are not allowed to store in one CD, they have to be stored them in two different CD, otherwise the software installation will get errors.

Q8: During the installation of Lexia-3, I got ERROR reading “Failure of the activation (error 20).

lexia 3 pp2000 error

A8: we are so sorry; we used to store the lexia3 pp2000 software and diagbox v6.01 software in the same one CD, now they are separately stored into two different CD. Please download diagbox V6.01 software at: and try to reinstall, if it does not work either, contact us we will ship you CD.

Detail Lexia 3 PP200 informationg please check:


carecar 發表在 痞客邦 留言(0) 人氣()